Analyze the Effect of Process Parameters in Deep Drawing of Stainless Steel 316

Main Article Content

Dhaval P. Shah
S. J. Chaudhary


One of the most common outcomes in deep drawing process is the defects that occur in the cup shell. These defects are caused by many parameters like blank holder force (BHF), Die Radius, Punch Radius, Blank diameter, friction between punch and blank and Die, normal anisotropy of material, blank thickness and many more. The main objectives of the present study are to determine the most critical process parameters that cause defects and thinning in the blanks. The effect of various process parameters will be determined by using Statistical as well as Experimental methods.


Download data is not yet available.


Metrics Loading ...

Article Details

How to Cite
Dhaval P. Shah, and S. J. Chaudhary. “Analyze the Effect of Process Parameters in Deep Drawing of Stainless Steel 316”. Technix International Journal for Engineering Research, vol. 1, no. 5, May 2014, pp. 119-28,
Research Articles


Ghosh and Malik “Manufacturing science” East-West Press (P) Ltd., New Delhi 1985.

J. Duncan, S.J.Hu, Z.Marciniak “Mechanics of sheet metal forming” Butterworth – Heinemann Publications, 2002.

Phillip Ross “Taguchi techniques for Quality Engineering”

Mark Colgan, John Monaghan, “Deep Drawing process: analysis and experiment”, Journal of Materials Processing Technology, 132, 2003, 35-41.

G. Venkateswarlu, M. J. Davidson and G. R. N. Tagore, Influence of process parameters on the cup drawing of aluminium 7075 sheet, International Journal of Engineering, Science and Technology Vol. 2, No. 11, 2010, pp. 41-49.

R. Padmanabhan, M.C. Oliveira, J.L. Alves, L.F. Menezes, “Influence of process parameters on the deep drawing of stainless steel”, Finite Elements in Analysis and Design 43 (2007) 1062 – 1067.

S. RAJU, G. GANESAN, R. KARTHIKEYAN, “Influence of variables in deep drawing of AA 6061 sheet” , Trans. Non-ferrous society of china 20(2010) 1856-1862.

Young Hoon Moon, Yong Kee Kang, Jin Wook Park, Sung Rak Gong, “Deep Drawing With Internal Air-Pressing to Increase The Limit Drawing Ratio of Aluminum Sheet”, KSME International Journal; VoL 15 No.4, pp. 459- 464, 2001.

Y. Marumo, H. Saiki, L Ruan, “Effect of sheet thickness on Deep Drawing of Metal Foils”, Journal of Achievements in Materials and Manufacturing Engineering VOLUME 20 ISSUES 1-2 January-February 2007, 479-482.

A. FallahiArezodar and A. Eghbali, “Evaluating the Parameters Affecting the Distribution of Thickness in Cup Deep drawing of ST14 Sheet” , Journal of Advanced Science and Engineering Research Vol 2, No 3 September (2012) 223-231.

Kopanathigowtham, K.V.N.S. Srikanth& K.L.N. Murty, “Simulation of the effect of die radius on deep drawing process, International Journal of Applied Research in Mechanical Engineering ISSN: 2231 –5950, Volume-2, Issue-1, 2012.

R. Venkat Reddy, Dr T.A. Janardhan Reddy, Dr. G.C.M. Reddy, “Effect of Various Parameters on the Wrinkling In Deep Drawing Cylindrical Cups”, International Journal of Engineering Trends and Technology- Volume3 Issue1- 2012.

H. Zein, M. El-Sherbiny, M. Abd-Rabou, M. El Shazly, “Effect of Die Design Parameters on Thinning of Sheet Metal in the Deep Drawing Process”, American Journal of Mechanical Engineering, 2013, Vol. 1, No. 2, 20-29.